Home/Journal

From the plant

paver pedestals: The tile stands on four points

A tile sits on four points. T-ST holds a 2–8 mm gap and turns 360 degrees. The stick does not pull lippage down. Lippage is the work of a TLS wedge. A deck clip is not written on this head.

A tile head on a line pressed in Çorlu takes the plate at four points. T-ST only holds the gap. Lippage comes down with TLS: tls-W for 5–13 mm, tls-S for 3–17 mm.

Tokoz Premium porcelain tile flooring

Porcelain or stone does not bond to a mortar bed. It sits on the corners of four heads. The middle is empty. An empty middle breaks if someone tries to carry the plate on two heads. The break comes from a short count of points before it comes from a thin tile. Each corner wants a head. A half tile at the edge wants two or three points. Skipping the third point leaves a free corner down. The corner left down lifts the lip of the full tile beside it. The lifted lip is taken for a fault of the joint stick. The fault is a missing point. A deck board is not written onto these four points. A board wants a clip tooth. A tile head does not carry that tooth.

Porcelain stands like a lid on four heads.
Porcelain stands like a lid on four heads.

T-ST holds the gap

The stick turns 360 degrees on the head. The gap it holds is 2 to 8 millimetres. The gap is the water path between two tiles. The stick does not correct one tile sitting higher than the other. The face that sits higher is called a lip. Crushing the lip with the stick closes the gap and leaves the water on the face. The range is a catalogue value. The joint on site comes from the maker of the tile. If the two do not meet, the stick changes, not the head. The stick is not written once per corner out of habit. A sparse joint wants a sparse stick. Few sticks in a tight joint lean the plates together. A leaning plate breaks the plane of the four points. A broken plane comes from a short count, not from the length of the stick.

T-ST holds the gap. It does not pull the lip down.
T-ST holds the gap. It does not pull the lip down.

The lip is another product

If the faces of two tiles are not in one plane, that is a lip. The piece that pulls the lip down is not T-ST. The piece that pulls it down is a Tokoz TLS wedge. The tls-W set is a wedge, a holder and pliers: tls-Ww, tls-Ws, tls-Wp. That set levels a covering 5 to 13 millimetres thick, with a joint of 1 to 3 millimetres. The tls-S set is a screw wedge: tls-Sw and tls-Ss. That set levels a thickness of 3 to 17 millimetres, with a joint of 1 to 2 millimetres, at edges and corners, by hand. The wedge is not fitted to the body of the pedestal. The wedge goes between the tiles for a while and comes out when the level is held. A wedge that does not come out blocks the joint. A blocked joint closes the water path that T-ST is holding. The two jobs are done at the same time, with separate pieces.

The lock keeps the tile from leaving the head in the wind.
The lock keeps the tile from leaving the head in the wind.

The wedge does not stay on the pedestal

TLS is not left inside the joint after the floor is finished. If it is left, the water path blocks and the stick is useless. Taking it out is done by hand. tls-S comes out by hand at edges and corners too. Taking the pliers for the screw of the head leads to reading the height off the wedge. The height is read off the body. The wedge only pulls two faces into one plane for a while. After the pull, the four points still carry the tile. The wedge is not a support. If it is taken for a support, the order writes the wedge count as the pedestal count. That writing leaves the pedestal box short and the wedge box long. Spare wedges pull lips down. A short pedestal leaves the corner empty. An empty corner lifts the pulled lip again the next day.

The pad spreads the tile’s load onto the membrane.
The pad spreads the tile’s load onto the membrane.

A deck clip is not written on this head

A tile head does not carry a board tooth. T-DCN holds the edge of a board and does not go under the corner of a tile. Writing both on the same module puts both the stick and the clip in the box, and the site leaves one of them idle. An idle piece does not do the work of the other. The stick does not become a clip. The clip does not become the wedge that pulls a lip down. Three pieces are three jobs. If tile and board are to stand side by side on one floor, the line splits in two. On the split line the head changes too. A head that does not change forces the board onto four points. A forced board flexes in the middle. The flex pulls the plane of the tile as well. A pulled plane looks like a lip and does not come down with a wedge. The reason it does not come down is the wrong head standing beside it.

The load is written once

The support under the tile is spoken of, in the Premium family, as one thousand kilograms at a point. That number is not the kilogram of the tile itself. The number is the declaration of one of the four points. The four points carry the same declaration. Writing the five-hundred-kilogram family on one point and the thousand-kilogram family on the next gives the corner two seats. Two seats make the lip look as if a wedge pulled it down, and bring it back the next day. The family stays the same across the whole tile field. Using the lighter family at the edge lifts the lip of the full tile from the edge. The lift is taken for the work of the wind. The work is the difference of family. The difference is cut on the sheet with one line: the family name once, the head count once.

The lock does not stand in for the lip

T-L holds the tile on the head so the wind does not lift the corner. Holding it does not pull two tiles into one face. The wedge does that pull. Tightening the lock to pull a lip down crushes the gap and bends the stick. A bent stick closes the water path. The lock closes after the lip has come down. If it is closed first, the wedge has nowhere to enter. A wedge with nowhere to enter leaves the corner free. A free corner is taken for something the lock is holding, and it reports itself at the first wind. The report does not mean the lock is weak. It means the order was backwards. The order is this. The four points sit. The wedge pulls the faces. The wedge comes out. The stick holds the gap. The lock closes.

The sheet keeps the stick apart from the wedge

On the sheet the tile size, the joint gap and the thickness of the covering stand apart. If the gap is outside 2 to 8 millimetres, T-ST is not written and another stick is looked for. If the thickness is between 5 and 13, a tls-W line is opened. If the thickness is between 3 and 17 and the work is at the edge, a tls-S line is opened. If both sets could take the thickness, one line remains, according to which hand tool the site will use. The pedestal count is not hidden inside these lines. The Premium point declaration is named once, not written again at every corner. The sheet that goes to Çorlu is one that has counted the four points, the stick and the wedge apart. An uncounted wedge makes the site crush the lip with the stick. A crushed gap stays on the face at the next rain.

Pedestal Premium · technical details · contact

← Journal
ig

Instagram

@tokoz_international

Follow on Instagram
  • Tokoz raised floor pedestals under outdoor lath flooring
  • Tokoz WPC deck and pedestals at a pool edge
  • Tokoz Premium adjustable flooring pedestal 1000 kg
  • Tokoz Clever pedestal under lath flooring
  • Tokoz Premium slope corrector on an adjustable pedestal
  • Tokoz Premium T-L lock accessory for pedestals
  • Tokoz orthopedic base pad T-P under a pedestal
  • Tokoz Clever slope head for pedestals
  • Tokoz TLS tile leveling clips and wedges on large-format tiles
  • Tokoz Ecogreen sedum trays on a green roof
  • Tokoz raised floor pedestals under outdoor lath flooring
  • Tokoz WPC deck and pedestals at a pool edge
  • Tokoz Premium adjustable flooring pedestal 1000 kg
  • Tokoz Clever pedestal under lath flooring
  • Tokoz Premium slope corrector on an adjustable pedestal
  • Tokoz Premium T-L lock accessory for pedestals
  • Tokoz orthopedic base pad T-P under a pedestal
  • Tokoz Clever slope head for pedestals
  • Tokoz TLS tile leveling clips and wedges on large-format tiles
  • Tokoz Ecogreen sedum trays on a green roof

Factory

Çorlu · Tekirdağ · Türkiye